Introduction #
Repairing the MGB Rubber Bumpers. This is a write up from John Mangles (known as “The MG Doc”) who ran his own business for decades. There’s some detailed photos at the end to help make the details below more visual to follow. Make sure you scroll all the way down.
Overview #
As a professional restorer, I’ve been asked many times how to repair / refinish the rubber bumpers of the MGB. After years of use, many bumpers have nicks and scratches as well as a weathered look due to sun bleaching. In this article, I’ll try to explain how to properly refresh their appearance.
As with any kind of repairs, proper safety equipment is a must. For this job I’ll use:
- a dust mask
- ear & eye protection for grinding / sanding
- a charcoal respirator for painting
- rubber gloves for the chemicals.
Be sure to read and follow the directions on all the products. Some can be hazardous to your health!
Tools and Supplies #
The tools needed will be:
- a grinder
- a sanding block or DA sander
- a small auto body filler spreader
- a blow gun (for compressed air)
- a heat gun.
Supplies needed will be:
- plenty of clean water
- plenty of clean lint-free rags
- a Scotch Brite ™ pad
- cleaning detergent; wax and grease remover
- 80, 180, 220, 320 and 400 grit sandpaper
- masking tape
- a flexible bumper repair kit
- flexible bumper paint
- not to mention plenty of elbow grease.
With this particular repair, I used a paint spray gun for the refinishing. However, the flexible bumper paint comes in an aerosol can if you don’t happen to have spray equipment. For ease of working, you might want to remove the bumper. I started with the bumper on the car then removed it for final sanding, cleaning, and painting.
Preparations #
Start by first removing all lights, bumper stickers, and the MG emblem. Then clean the bumper with a good quality wax and grease remover. I used DuPont’s Prep-Sol ™ #3919S following the directions on the can. Next, wash the bumper with a cleanser such as Fantastic or 409 and the Scotch Brite pad – scrubbing it to within an inch of its life. Then rinse it with plenty of clean water. Now you are ready to make the repairs.
The Repair Process #
Start by sanding the bumper (every bit of it) with the 80-grit sandpaper to remove any and all of the paint from the surface. I used a DA type air sander; but it can be done by hand, it just takes longer. Clean all sanding dust from surface then wash and dry using clean, lint-free towels.
Some dents and deformations can usually be removed using a paint stripping heat gun. To do this, play the heat on the inside (if possible) and outside of the area until it softens a bit. Be careful not to heat too much or you’ll have more repairs to do. As the area softens, pull or push the area into place, using your fingers (careful, it’s HOT) or some other sort of tool and then cool it down using cool water. If the area does not respond properly, heat and cool until it does.
For scratches, nicks, gouges, and some small tears, start by sanding / grinding the effected area to roughen it up a bit and remove any loose pieces. Fill the effected area by mixing a small amount of the flexible repair filler (following the directions on the package) and evenly coat the entire surface of the bumper using the auto body filler spreader. You may not be able to cover the entire surface with the amount you mixed so continue mixing more until the surface is covered. The flexible repair that I used can be worked for about 5 minutes and sets in about 15 minutes. It will set up faster in warm weather and slower in cooler weather.
When the filler sets up (cures), it will be smooth to the touch. Filler that has not completely cured will feel sticky and will not sand well at all. Once the filler has cured, start by sanding with 180-grit sandpaper using a sanding block or sander until smooth. If there are still small imperfections, spread another coat on the effected area and sand smooth. When the surface is smooth to your liking and all of the imperfections are removed, wet sand the entire surface. Use 220-grit, wet or dry sandpaper with plenty of clean water. Rinse and dry again, using the lint free towels.
With the bumper completely sanded, cleaned and dried, you are ready to start the refinishing. Again, read and follow all instructions on the paint can and use your safety equipment!
Painting #
Start by applying two medium wet coats of the flexible bumper paint. Be sure to let it flash-off (dry to dull finish) between coats. So. when dry, usually in about 30 to 45 minutes depending on temperature and humidity, wet sand with 320-grit wet or dry sandpaper again. Use plenty of clean water. Rinse and dry. Apply one to two more, medium wet coats of flexible paint.Allow proper dry time. Then wet sand with 400-grit sandpaper. Rinse and dry, lint free towels again.
The surface should now be ready for the final coat of paint. Let the final coat of paint dry overnight then reassemble and reinstall the bumper. Your finish should have a smooth, semi-gloss finish.
Step by Step in Pictures – Repairing the MGB Rubber Bumpers #
Before repairs. Notice the dull, crazed finish. Home restorers should remove bumpers first
What you’ll need
Bumper after cleaning with wax & grease remover and initial sanding
Here you can see the bumper after filler is applied and before sanding
Showing the bumper after sanding the filler
Automix filler
Automix filler before mixing
Bumper after final sanding and ready for finish
Flexible bumper paint
The finished product
So, there you have it, the process for Repairing the MGB Rubber Bumpers.
Other Materials #
I’ve built this website and spent time on the knowledge base to bring together a lot of information I have collected from around the internet. The intent is making it easy to find rather than having to know about and have skills with search engine query terms to get what you were looking for. Please make use of the knowledge base.
